Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 6 7/25/2014
Note: The intent was to highlight to the system designer that early coordination with an
aircraft original equipment manufacturer (OEM) is important to minimize the
compliance requirements at the time of installation, and that even without an
OEM, the guidance is relevant when installing the system.
c. Guidance for the use of RTCA Documents DO-325 and DO-336.
(1) RTCA Document DO-325 identifies the typical functions of an AFGCS. We
recommend that AFGCS equipment manufacturers obtain technical standard order
authorization (TSOA) for TSO-C198 to minimize compliance showings that would be
required at installation approval stage. There should be a declaration of any non-TSO
functions in the TSOA application so there can be an appropriate evaluation and
acceptance of the software and hardware qualification data related to those functions. If
AFGCS equipment does not have TSOA for TSO-C198, the applicant for installation
approval would have to show compliance with the DO-325 MOPS, as appropriate to
functions provided, and conduct the necessary software and hardware qualifications
defined in DO-178 and DO-254 guidance documents.
(2) RTCA Document DO-336 has two primary focus items: to highlight the
requirements for a proper safety assessment (Chapter 8) and to highlight the
compliance demonstration (Chapter 9). Each of these should be discussed with the
appropriate Aircraft Certification Office (ACO) very early in the program and included in
the certification plan.
d. References.
(1) 14 CFR Regulations (available at http://rgl.faa.gov/):
Section Title
27.671 General. (Control Systems)
Stability augmentation, automatic, and power-operated 27.672 systems.
27.1309 Equipment, systems, and installations.
27.1329 Automatic pilot system.
27.1335 Flight director systems.
Appendix B Airworthiness Criteria for Helicopter Instrument Flight to Part 27
(2) TSOs (available at http://rgl.faa.gov/):
TSO Title
Automatic Flight Guidance and Control system (AFGCS) TSO-C198 Equipment
Page MG 23 - 2
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.