Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 2 4/12/06
(C) Representation of OEI training alerts with respect to the actual case for
which the system is designed. Lack of complete representation of the OEI training
alerts can be accepted and documented in the rotorcraft flight manual (RFM).
(7) Representativeness of the maneuver. Although the final decision on the use of
the system for training purposes is the responsibility of the national operational
authority, the applicant and certificating authority should ensure that the system
adequately represents the actual maneuvers the system is designed to simulate. In this
regard, the certification team should:
(i) Ensure that the engine failure dynamics of the training mode favorably
compare with an actual engine failure. This can be accomplished by comparing the
time histories of Ng/torque during an actual engine failure and a training mode engine
failure.
(ii) Qualitatively evaluate the piloting techniques required for the training
maneuver and the maneuvers used for certification. Ensure the techniques are
sufficiently similar to provide adequate training.
(iii) If the training mode does not adequately replicate portions of an OEI event,
to include a realistic reproduction of the resultant flight path, those areas should be
identified in the RFM (e.g., “The OEI training mode does not accurately represent
second stage climb performance.”).
(8) Limitations and Performance Charts.
(i) RFM data necessary for the use of the system typically include:
(A) Weight limitations for training.
(B) Performances associated to the system operative (e.g., rate of climb,
take off, landing distances).
(ii) This data should be validated by actual tests or analysis validated by tests or
a combination of both to assure the same level of accuracy as the other RFM data.
(9) RFM. The RFM should contain the following information:
(i) Description of the system and its functions.
(ii) Clear statement on the scope of the training mode and the extent of the
validity of the system.
(iii) Limited to essential crew only.
Page MG 22 - 4
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.