Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
CHAPTER 3
AIRWORTHINESS STANDARDS
NORMAL CATEGORY ROTORCRAFT
MISCELLANEOUS GUIDANCE (MG)
AC 27 MG 7. HOUR METERS OR TIME-IN-SERVICE RECORDING DEVICES IN
ROTORCRAFT.
a. Explanation.
(1) Time in service is a required maintenance record according to
§ 91.173(a)(2)(i). Manual recording (rather than automatic) of the rotorcraft time in
service is required whether or not the rotorcraft is equipped with a time accumulating
device or hour meter. Time recording devices (hour meters) are optional and not
required by the maintenance or operating rules or as a part of the aircraft type design.
(2) Time in service is defined in FAR Part 1 as follows: “...with respect to
maintenance time records, means the time from the moment an aircraft leaves the
surface of the earth until it touches it at the next point of landing.”
(3) The allowable total time in service, that is, service life or retirement time,
has been typically specified for critical rotorcraft components that were subject to
fatigue. The life was determined under § 27.571 or its predecessor standards.
(4) Hour meters may be mechanical and a part of a recording tachometer.
They may be electrical and activated by the main battery switch, engine oil pressure, or
some other source. These devices may not record “real time” when an engine or rotor
is at idle speed or when deactivated by an oil pressure sensor switch. This real time
omission is not considered significant in the life of a rotorcraft if the design and
installation of the sensor minimizes this omission. However, for an individual aircraft
that is used extensively, the omission of real time may become significant, and the time
in service should be adjusted prior to recording the time in service in the aircraft
records.
b. Procedures.
(1) Time in service must be recorded in the aircraft maintenance records.
(2) Hour meters are used to accumulate operating time. The meters may be
activated by various sensors/switches. The type design data should include hour meter
installation data including the sensor/switch location and any adjustment or “rigging”
information to ensure proper installation.
(3) One acceptable installation of a sensor/switch would activate the hour meter
whenever the collective pitch control was moved from the lowest pitch stop position.
Page MG 7 - 1
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.