Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 9/17/2009
AC 27.49. § 27.49 (Former § 27.73) (Amendment 27-44) Performance at
Minimum Operating Speed.
(For § 27.73 prior to Amendment 27-44, see AC 27.73)
a. Explanation. Amendment 27-44 adds a requirement to determine out-of-ground
effect (OGE) hover performance. Once reserved for special missions, OGE operations
are now a common practice.
(1) The word "hover" applies to a helicopter that is airborne at a given altitude
over a fixed geographical point regardless of wind. Pure hover is accomplished only in
still air. For the purpose of this manual, the word "hover" will mean pure hover.
(2) The regulatory requirement for hover performance, § 27.49, refers to hover
in–ground-effect (IGE) and OGE. Hover OGE is the absence of measurable ground
effect. Hover OGE is established when the power required to hover is the same at
different heights above the ground.
(3) The objective of hover performance tests is to determine the power required
to hover at different gross weights, ambient temperatures, and pressure altitudes.
Using non-dimensional power coefficients (Cp) and thrust coefficients (Ct) for
normalizing and presenting test results minimizes the amount of data required to cover
the helicopter's operating envelope.
(4) Hover performance tests must be conducted over a sufficient range of pressure
altitudes and weights to cover the approved ranges of those variables for takeoff and
landing. Additional data should be acquired during cold ambient temperatures,
especially at high altitudes, to account for possible Mach effects.
(5) The IGE hover ceiling for which data should be obtained and subsequently
presented in the flight manual should be the same height consistent with the minimum
hover height demonstrated during the takeoff tests. Refer to AC 27.51 for the
procedure to determine this hover height.
b. Procedures.
(1) Two methods of acquiring hover performance data are the tethered and the
free flight techniques. The tethered technique is accomplished by tethering the
rotorcraft to the ground using a cable and load cell. The load cell and cable are
attached to the ground tie-down and to the rotorcraft cargo hook. The load cell is used
to measure the rotorcraft's pull on the cable. Hover heights are based on skid or wheel
height above the ground. During tethered hover tests, the rotorcraft should be at light
gross weight. The rotorcraft will be stabilized at a fixed power setting and rotor speed at
the appropriate skid or wheel height. Once the required data are obtained, power
should be varied from the minimum to the maximum allowed at various rotor RPM. This
technique will produce a large Ct/Cp spread. The load cell reading is recorded for each
Page B - 24 2
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.