FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page F-52.1

PDF page 640 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 640
AC 27-1B · F-52.1Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

6/23/23                                         AC 27-1B, Chg 9

AC 27.1329B. § 27.1329 (AMENDMENT 27-51) AUTOMATIC PILOT AND FLIGHT
GUIDANCE SYSTEM


    a. Explanation. Amendment 27-51 changed the section heading name to
“Automatic pilot and flight guidance system” and combined the requirements for
automatic pilot (14 CFR 27.1329) and flight director systems (14 CFR 27.1335) into one
rule (14 CFR 27.1329). The amendment also removed 14 CFR 27.1335.

    b. Procedures. This section of the AC is updated to include the guidance previously
found in AC 27-1B Section 27.1335. Therefore, the guidance pertaining to section
27.1329 of this AC remains in effect with the following additions:


        (1) Three-cue flight directors for rotorcraft use the usual pitch and roll command
cues with the third cue displayed on the left side of the attitude director indicator (ADI).
These instruments can be used in either the two-axes or three-axes modes. In either
mode, the lateral command cue controls the roll attitude, and the vertical command cue
controls the pitch attitude. The rotorcraft attitude, controlled by the cyclic control, is
changed to satisfy the flight director commands. The third cue, when displayed,
commands collective pitch position and is used when an airspeed or pitch attitude mode
and a vertical mode (altitude hold, glide slope, etc.) are selected.

        (2) The general convention for flight director design is that each command bar is
a “fly to” command. The motion of the flight director indicator is such to command a
corresponding sense of control system motion. This is true of flight director pitch and roll
commands and should hold true for additional commands such as collective pitch.

        (3) Some consideration should be given to the collective, or third cue, display.
For example, if the collective symbol is selected as the fixed index, the command cue
and collective pitch control should move in opposite directions when collective pitch
changes are made. This configuration would constitute a conventional “fly to” indicator.
 If the collective symbol is selected for the movable index, the direction of motion of the
collective symbol will coincide with the direction of collective pitch changes. In this case
the moving collective symbol does not comply with the “fly to” convention; however, this
configuration has been approved by the FAA with special symbology, special
background effects, and special color coding and has performed satisfactorily in service.

        (4) The recommended display for a three-cue flight director incorporates the
standard pitch and roll command symbols: either pitch and roll bars or the “V” bar
display. The third cue, or collective symbol, should be located on the left side of the ADI.
The shape of the moving cue and the background display should be unique to avoid it
being confused with a glide slope display or angle of attack display. One display uses a
third cue, shaped like a small handle, to aid in identifying it as the collective pitch
symbol.



                               Page F - 52.1

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →