Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
AC 27.33. § 27.33 (Amendment 27-14) MAIN ROTOR SPEED AND PITCH LIMITS.
a. Explanation.
(1) General. This section requires the establishment of power-on and power-off
main rotor speed limits and the requirements for low rotor speed warning.
(2) Power-On. The power-on limits should be sufficient to maintain the rotor
speed within these limits during any appropriate maneuver expected to be encountered
in normal operations throughout the flight envelope for which certification is requested.
In the past a minimum power-on range of approximately 3 percent has been required
due to engine governor and engine operating characteristics. With the introduction of
advanced engines and electronic engine controls, there may not be a need for a range.
One fixed value may suffice. If substantiated, transient power-on values may also be
acceptable.
(3) Power-Off. The power-off rotor speed limits should be sufficient to
encompass the rotor speeds encountered during normal autorotative maneuvers except
for final landing phase (touchdown) for which rotor RPM may be lower than the
minimum transient limit for flight, provided stress limits are not exceeded. The limits
should also be sufficient to cover the ranges of airspeed, weight, and altitudes for which
certification is requested. It is not the intent of the rule to require the minimum and
maximum limit values in conjunction with extremes such as maximum/minimum weights
and/or high altitude. The minimum and maximum rotor speed requirements should be
thoroughly evaluated at normal operating environment; i.e., at altitudes from
approximately sea level to 10,000 feet, temperatures not at extremes, and weights as
necessary for other tests and as required to readily establish the limit rotor speeds.
Spot checks of the autorotative requirements should be made at the extremes of the
flight envelope and environmental conditions during normal tests at those conditions.
Under conditions where high autorotative rotor speeds may be encountered, it is
acceptable for the pilot to adjust the controls to prevent overspeeding of the rotor. At
light weight combined with low altitudes and extremely cold temperatures, the normal
low pitch setting may not be sufficient to maintain autorotational rotor speed values
within limits. If this occurs, the manufacturer may elect to adjust the low pitch stops as a
maintenance procedure at extreme ambient conditions provided the flight and
maintenance manuals clearly present the rigging requirements and procedures. There
must be sufficient “overlap” of ambient conditions between configurations such that
rerigging is not required whenever ambient temperature and surface elevation change
slightly. Any downrigging of the low pitch stop must continue to ensure adequate
clearance between controls and other rotorcraft structure and should be evaluated
during flight test. Both the power-on and power-off limits may also be established by
encountering critical flapping limits in some approved flight conditions such as high
airspeed or sideward flight.
(4) Low Speed Warning. If it is possible under expected operating conditions
for the rotor speed to fall below the minimum approved values, the requirement exists
Page B – 7
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.