Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
AC 27.27.§ 27.27 (Amendment 27-2) CENTER OF GRAVITY LIMITS.
a. Explanation.
(1) This regulation is definitive and requires that the center of gravity limits be
defined. Proof of compliance with all applicable flight requirements is required within
the range of established CG’s. Along with the longitudinal CG limits, the lateral CG
limits should either be established or determined to be not critical.
(2) Ballast is usually carried during the flight test program to investigate the
approved gross weight/center of gravity limits. Lead is the most commonly used form of
ballast during rotorcraft flight testing although other types of ballast, such as water, may
serve just as well. Water may have the added benefit of being jettisonable during
critical flight test conditions. Care must be taken regarding the location of ballast. The
strength of the supporting structures should be adequate to support such ballast during
the flight loads that may be imposed during a particular test and for the ultimate inertia
forces of § 29.561(b)(3). Of critical importance is the method of securing the ballast to
the desired locations. To avoid any undesired in-flight movements of the ballast, a
positive method of constraint is mandatory. The flight test crews should also visually
verify the amount, location, and integrity of the ballast. The effects of mass moment of
inertia on the flight characteristics due to the ballast locations should also be
considered. The mass moment of inertia of the test rotorcraft should, to the extent
possible, be the same as that expected in normal, approved loadings, especially during
tests involving dynamic inputs.
b. Procedures.
(1) Center of gravity locations and limits are of prime importance to rotorcraft
stability and safety in flight. The primary concern is establishment of the longitudinal
center of gravity limits. Lateral center of gravity limits with respect to longitudinal center
of gravity limits are also important. The design of the rotorcraft is usually such that
approximate lateral symmetry exists. This lateral symmetry can be upset by numerous
probable lateral loadings possibly resulting in the necessity to establish lateral center of
gravity limits. Stability and control characteristics may be seriously affected by loading
outside the established center of gravity limits. The established center of gravity limits
must be that as fuel is consumed, it is possible for the rotorcraft to remain within the
established limits by acceptable loading and/or operating instructions.
(2) Structural limits may restrict the maximum forward longitudinal center of
gravity limits. However, in most cases it is the maximum value established wherein
adequate low speed control power exists to meet such requirements as § 27.143(c).
Likewise, the maximum aft center of gravity limit may be a “structural limit,” but it usually
is determined during flight test after the rotorcraft’s handling qualities tests have been
conducted. Flight tests may reduce the “structural limit” CG envelope, but flight tests
alone should not be used to expand the “structural limit.” Additional items which may
influence the maximum aft center of gravity limits may be malfunctions of automatic
Page B – 4.2
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.