Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
SUBPART E - POWERPLANT
COOLING
AC 27.1041. § 27.1041 (Amendment 27-2) COOLING--GENERAL.
a. Explanation. The rotorcraft design should provide for cooling to maintain the
temperature of all powerplant and power transmission components and fluids within the
limitations established for the items. Cooling provisions should be adequate for
shutdown and for water, ground, and flight operating conditions. The adequacy of the
cooling provisions should be demonstrated by flight testing.
b. Procedures.
(1) Test conditions and procedures necessary to demonstrate adequate cooling
for water, ground, flight, and shutdown conditions should be agreed upon between the
applicant and the FAA/AUTHORITY certification engineer. A cooling test proposal
which defines the agreed test points and procedures should be prepared well in
advance of the official certification testing.
(2) The test conditions selected would typically include climb, cruise, hover, and
shutdown after a prolonged hover. Hover OGE should be evaluated if sling load
operation is envisioned for the rotorcraft. One test condition which should be examined,
particularly with regard to transmission cooling, is the point of highest multiengine
mechanical power at the maximum ambient temperature. This is identified as test point
“A” in figure AC 27.1041-1. The selection of test points should be tempered with
engineering judgment and based on results from similar aircraft if such data are
available. In showing compliance with the cooling requirements, the applicant should
not be required to exceed rotorcraft established limits (gross weight, drive system
torque, measured gas temperature, etc.), aircraft power required, or power available.
The applicant may elect, however, to exceed these limits in order to minimize test points
by conservative testing, or to anticipate future growth (increased gross weight, etc.).
(3) The need for a comprehensive cooling test plan prior to certification testing
cannot be overemphasized. Highly derated engine installations, the relationship of
power required to power available, the use of bleed air devices which would increase
the measured gas temperature while aircraft power required remains the same, auxiliary
cooling provisions, and the increase in engine temperatures with engine deterioration
are factors which could affect the selection of cooling demonstration test points.
Page E - 92
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.