FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-93

PDF page 366 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 366
AC 27-1B · D-93Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

past to obtain the effects of fuselage deformation on exit clearances during minor crash
landings.

AC 27.807A.    § 27.807 (Amendment 27-26) EMERGENCY EXITS.

     a. Explanation. Amendment 27-26 added § 27.807(d)(3) which requires proof that
all rotorcraft ditching configuration exits will also be free of interference from emergency
flotation devices, whether stowed or deployed (inflated).

     b. Procedures. All of the policy material pertaining to this section remains in effect
with the following additions:

         (1) Test, demonstration, compliance inspection, or analysis is required to show
the “ditching” exits are free from interference from stowed/deployed emergency flotation
devices. In the event an analysis is insufficient or a given design is questionable, a
demonstrating may be required. The demonstration would consist, as a minimum, of an
accurate, full-size replica (or representation) of the rotorcraft and of the flotation devices
both before, during, an after their deployment.

         (2) The type inspection authorization may be used to perform a detailed
compliance evaluation utilizing a full-scale rotorcraft in calm water.

         (3) Designs may be accepted “by compliance visual inspection” if location of
exit and flotation devices relative to each other ensure that interference is impossible.
In this case, a demonstration is unnecessary.

AC 27.807B § 27.807 (Amendment 27-37) EMERGENCY EXITS.

     a. Explanation.

         (1) Amendment 27-37 increases the maximum gross weight of a normal
category rotorcraft from 6000 pounds to 7000 pounds and adds a passenger seat
limitation of nine. In conjunction with the weight and passenger limitation and to support
a potential increase of passengers, § 27.807 was completely rewritten to include the
previous requirements but was revised to require at least one emergency exit on each
side of the cabin readily accessible for each passenger. This is required regardless of
whether the rotorcraft has a closed cabin or is ditching certified. In addition, at least one
of the required exits must be usable in any probable attitude that may result from a
crash. Doors intended for use during normal operations may also serve as emergency
exits provided these doors comply with requirements specified for emergency exits..

         (2) Each emergency exit must provide an unobstructed minimum opening
equivalent to a 19-inch x 26-inch ellipse. The methods of opening or operating the
emergency exit must be simple and obvious from both inside and outside the rotorcraft.




                                                       Page D - 93

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →