FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page D-17

PDF page 286 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 286
AC 27-1B · D-17Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


         (1) One example of fitting factor use follows:

          1,000-pound limit design load x 1.15 fitting factor x 1.5 ultimate load
             factor equals 1,725-pound ultimate design load.

         (2) Other specific factors may be similarly applied. Refer to §§ 27.623 and
27.625.

         (3) Other factors may be imposed as cited in the rule. Advisory
Circular 20-107, paragraphs 5 and 6, are examples of requiring tests of component and
subcomponent structure to account for variability of strength and stiffness of composite
structures. Factors appropriate for the particular design are obtained and used in
substantiation of the composite structure.

         (4) The rule complements §§ 27.603 and 27.613. Regardless of the rule
invoked, the variability of the material and/or assembly properties should be accounted
for.

AC 27.621.  § 27.621 CASTING FACTORS.

     a. Explanation. Casting design, test, and inspection criteria are included in this
rule for critical and noncritical structural castings. Hydraulic or other fluid containers are
not subjected to “structural loads” but are subject to pressure testing as a part of
hydraulic or other flight systems. Critical and noncritical castings are defined in the rule.

         (1) Factors, tests, and inspections are specified for structural castings.
Additional factors, tests, and inspections may be applied, as prescribed by § 27.603,
§ 27.605, or § 27.613, for foundry quality control.

         (2) For castings that have surfaces subject to bearing structural design loads,
the casting factor need not exceed 1.25 with respect to bearing stresses and need not
be used with respect to the bearing surfaces if the bearing factor of § 27.623 exceeds
the applicable casting factor.

         (3) Critical castings must have a casting factor not less than 1.25 and must
receive 100 percent inspection as specified including radiographic inspection. Static
test requirements are also specified in addition to the inspection requirements.

         (4) Noncritical structural castings may have a casting factor as small as 1.0 with
attendant increased inspection and quality control requirements. Use of larger casting
factors reduces the inspection and quality control requirements.

         (5) Structural static and fatigue substantiation, by test or analysis, is still
required in addition to any casting static tests required by this rule.



                                                       Page D - 17

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →