Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
AC 27.607. § 27.607 (Amendment 27-4) FASTENERS.
a. Explanation. Section 27.607 of Amendment 27-4 requires dual locking
removable fasteners in critical locations. A nonfriction locking device is specifically
required in any bolt subject to rotation, as stated in the rules.
b. Procedures. Advisory Circular 20-71 contains information, procedures, and
means of complying with § 27.607 of Amendment 27-4.
AC 27.609. § 27.609 PROTECTION OF STRUCTURE.
a. Explanation. The structure should be suitably protected as specified in the rule
to maintain its design strength. Ventilation and drainage provisions must be provided as
specified in the rule. Overboard drains should be furnished for corrosive or waste
liquids. Drains for flammable fluids are specified in other rules such as §§ 27.999 and
27.1193.
b. Procedures.
(1) The structure may be preserved, painted, or treated with chemical films to
protect it from strength deterioration. An approved process specification should be used
for these types of treatments.
(2) Parts may be plated or chemically treated, such as anodized, for protection.
An evaluation and substantiation may be required to ensure the structure or parts are
not adversely affected during, or as a result of, the plating or treatment process.
(§ 27.605 concerns approval of process specifications and fabrication methods.)
(3) Plating or material surface hardness or composition changes may require
fatigue substantiation to ensure the fatigue strength is not altered or is otherwise
properly assessed. An approved process specification should be used for these types
of treatments.
(4) To prevent water accumulation, drain holes should be placed at possible
dams such as bulkheads and at low points in the fuselage and in the stabilizing
surfaces.
(5) Control tubes and tubes used as primary mount structures (i.e.,
transmission support structure and engine mount structure) should be designed to
prevent entry and collection of corrosive fluids or vapor, including water.
(i) A closed insert in each tube end may be used.
(ii) A sealant applied around the tube ends and around each rivet head
may be used.
Page D - 6
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.