FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 131

PDF page 131 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 131
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27.1B, Chg4                                                      3/31/2014


data because collective and throttle are not moved as airspeed is changed at a constant
altitude. A typical sequence of speeds that could produce these results would be:
150 (VH), 135 (0.9VH) trim speed, 125, 145, 115, 155, 105, and 165.

              (v)   For rotorcraft with high rates of climb, a series of climbs, each at a
different speed, may be required through a given altitude, utilizing sensitive
instrumentation to ensure collective position is the same for each data point. In
autorotation, a similar case arises and a series of descents, each at a different speed,
may be required through a given altitude band, using sensitive instrumentation to
ensure a repeatable collective position.

               (vi)  Hover tests should be conducted by maintaining an approximately
constant altitude above the ground at the hover height established for performance
purposes. The test altitude above the ground may be increased to provide reasonable
ground clearance during rearward flight. Groundspeed is varied using a pace vehicle,
theodolite, or other velocity measuring equipment. A pace vehicle is an aid in
maintaining an accurate hover height. The pilot can accurately maintain height by
controlling his sight picture of the pace vehicle (level with the roof, antenna, etc.). Hover
stability tests are ordinarily conducted in conjunction with hover controllability tests
because instrumentation and facilities are essentially the same.

                (vii)  Normally, climb, cruise, and autorotation tests should be conducted at
low, medium, and high altitudes. See paragraph AC 27.45 for guidance on interpolation
and extrapolation. High speed stability has been critical during cold weather testing. In
two recent models, VNE at cold temperatures has been limited by the stability
requirements of § 27.175(b). Cold weather testing should be accomplished or a
conservative approach for advancing blade tip Mach number should be used to limit
cold weather VNE to tip Mach number values demonstrated during warm weather
testing.

                 (viii) Hover stability should be verified at low altitude and, if required, at
high altitude. Refer to paragraph AC 27.45b(2) for guidance on expansion and
extrapolation of altitude.





Page B – 60

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →