FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 129

PDF page 129 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 129
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27.1B, Chg4                                                      3/31/2014


AC 27.175.  § 27.175 (Amendment 27-21) DEMONSTRATION OF STATIC
          LONGITUDINAL STABILITY.

     a. Explanation.

         (1) This rule incorporates the specific flight requirements for demonstration of
static longitudinal stability. Specific loadings, configurations, power levels, and speed
ranges are stated for conditions of climb, cruise, autorotation, and hover.

         (2) Some rotorcraft in forward flight experience significant changes in engine
power with changes in airspeed even though collective and throttle controls are held
fixed and altitude remains relatively constant. For these cases, the guidance in
§ 27.173 which states that throttle and collective pitch must be held constant is
appropriate for administration of this rule, and the specified power in § 27.175(a), (b),
and (c) should be considered as power established at initial trim conditions. This will
result in slightly higher or lower torque readings at “off trim” conditions. Collective and
throttle controls are held constant when obtaining data during climb, cruise, and
autorotation tests.

         (3) The effects of rotor RPM on autorotative static stability should be
determined and positive stability demonstrated for the most critical RPM. Values for
RPM can be expected to change as airspeed is varied from the “trimmed” condition.
The manufacturer’s recommended autorotation airspeed is ordinarily used for trim.

         (4) Hovering is considered a flight maneuver for which the pilot repeatedly
adjusts collective to maintain an approximately constant altitude above the ground. For
hover stability tests, collective and throttle adjustments are made as necessary to
maintain an approximately constant height above the ground. Also, a limited amount of
negative longitudinal control travel is allowed with changes in speed.

     b. Procedures.

         (1) Instrumentation.

                  (i)    Sensitive control position instrumentation is mandatory. Engine power
parameters should be recorded at trim. For testing of minor modifications or when
using a “before and after” method, a tape measure or a stick plotting board may be
utilized. A stick plotting board consists of a level surface with a clean sheet of paper on
it attached to the cockpit or seat structure. The installation must not interfere when the
flight controls are fully displaced. A recording pencil is attached to the cyclic control by
an offsetting arm in such a manner that it can be pushed down on the board to record
relative cyclic position at key times during test maneuvers. The figure AC 27.175-1 plot
is a typical presentation of longitudinal static stability.

                   (ii)   Other necessary parameters include pressure altitude, ambient
temperature, and indicated airspeed (pace vehicle or theodolite speed for hover tests).


Page B – 58

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →