FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page Apdx A-64

PDF page 1167 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 1167
AC 27-1B · Apdx A-64Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 1                                                                  2/12/03

                                    (MANUAL IDENTIFICATION)
                       ATTACHMENT 4
                      TYPE DESIGN CHANGE
                   ICA RECOMMENDED PROCEDURES
                                      (Continued)

                       Twidget Type Design Change Attachment 2

1. Use the list of appliances and modifications required for that Type Design Change (TDC) to
determine which ATA chapters of the original rotorcraft manufacturer's maintenance manual the
TDC will affect and which additional ATA chapters will be affected.

2.  The following are component and systems that will be affected by the Twidget TDC:
     a.  Fuselage structure will be modified to mount twidget arm assembly.
     b.  Cabin door will be modified.
     c.   Electrical power will be required for electrical motor.
     d.  Hydraulic power source will be required for deploying and storing twidget arm.
     e.  Twidget control assembly will be installed in the cabin.
       f.  Control will be mounted in cockpit for emergency release of the twidget..
     g. An Instrument will be installed in instrument panel indicating twidget's position.
     h. Twidget recording equipment and monitor will be mounted in cabin.
      i.  Twidget antenna will be mounted on belly of fuselage.
      j.  Cables and wiring will be routed through rotorcraft.
     k. Two-way communication will be required between the pilot and twidget operator.
      I.  Twidget gearbox requires servicing to full mark on site gage every 50 hours.
   m. Twidget arm assemblies and clutch requires lubrication every 100 hours.
    n.  Twidget installation requires an inspection every 300 hours.
    o.  Twidget arm assembly requires an ultrasonic test every 600 hours.
     p. Clutch has a wear tolerance of 1.56 mm.
    q.  Clutch is life-limited to be replaced every l,000 hours time in service.
     r. Twidget gearbox is required to be overhauled every l,000 hours time in service.
     s. Twidget gearbox attach bolt torque is 75-ft lb. and twidget arm assembly torque is 110 in
          lb.
      t.  Warning: Twidget should be retracted during takeoff, landing, and cruise above 85 knots.
     u. Caution: Do not tow or taxi the rotorcraft with the twidget arm deployed.
     v. Placards are required on the twidget unit and in the cockpit.

3. This example TDC will affect ATA-100 chapters: 4 Airworthiness Limitations, 5 Inspection, 6
Dimensions, 9 Towing and Taxiing, 10 Parking and Mooring, 11 Placards, 12 Servicing, 23
Communication, 24 Electrical, 25 Furnishings, 29 Hydraulic, 31 Indication and Recording, 52
Doors, and 53 Fuselage. A Chapter1 Introduction is also needed.


REVISION:                                                     (DATE)
Revision 4                                                            Page 3


Page Apdx A - 64

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →