Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
4/25/06 AC 27-1B, Chg 2
(MANUAL IDENTIFICATION)
REQUIREMENTS
(Continued)
13. WORK RECOMMENDED
The work recommended at these periods when each path of the rotorcraft was cleaned,
inspected, adjusted, tested, and lubricated. Reference Appendix A, A27.3 (b)(1). This is
required when applicant determines that work will be recommended for that part of the
rotorcraft at that period. When maintenance tasks are associated with cleaning, inspecting,
adjusting, testing or lubrication of each part of the rotorcraft and its engine(s), auxiliary power
unit, rotor(s), accessories, instruments and equipment, then those tasks should be included in the
ICA. This information is normally contained in the chapters that the work is required.
14. APPLICABLE WEAR TOLERANCES
The applicable wear tolerances. Reference Appendix A, A27.3 (b)(1). This is required when
applicant determines that wear tolerances will be required for the rotorcraft, its engine(s),
rotor(s), and appliances. When a procedure requires maintenance personnel to determine
whether the item being inspected or maintained meets a standard, the ICA should include the
standard and specify how much wear is acceptable. The tolerances are normally contained in
the chapter addressing the tolerance.
15. TROUBLESHOOTING
Troubleshooting information describing:
a. Probable malfunctions.
b. How to recognize those malfunctions. (Probable Cause). Some malfunctions could
be identified on the basis of a baseline vibration signature provided as follows in the
maintenance manual:
The baseline vibration characteristics of the basic aircraft configuration to be used for
maintenance or trouble shooting purposes should be provided as the vibratory aircraft
reference in the maintenance manual. These characteristics should be given for specified
loading and flight conditions (speed, altitude) with vibration pickups at specified airframe
locations decided by the manufacturer. The characteristics should be given as a typical range
of vibration levels at these locations and for the most representative frequencies and
directions for the rotorcraft concerned (N omega main rotor and n omega tail rotor...). The
manufacturers and operators should keep the basic vibration data updated from field/service
experience.
c. The remedial (corrective) action for those malfunctions.
Reference Appendix A, A27.3 (b)(2). This is required when applicant determines the rotorcraft,
its engine(s), rotor(s), and appliances require troubleshooting.
REVISION: (PAGE NUMBER)
Revision 3 ( )-00-00 Page 5
Page Apdx A - 47
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.