FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page Apdx A-23

PDF page 1126 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 1126
AC 27-1B · Apdx A-23Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                          AC 27-1B, Chg 1

                                      (MANUAL IDENTIFICATION)

                        CHAPTER 5
        INSPECTION REQUIREMENTS AND OVERHAUL SCHEDULE

1. INSPECTION REQUIREMENTS ­
   a. The ICA must include:
      (1) The recommended period at which each part of the rotorcraft and its engine(s),
auxiliary power unit, rotor(s), accessories, instruments and equipment shall be inspected.
Reference Appendix A, A27.3 (b)(1).
      (2) The degree (scope) of the inspection for each part of the rotorcraft and its engine(s),
auxiliary power unit, rotor(s), accessories, instruments and equipment. Reference Appendix
A, A27.3 (b)(1).
      (3) An inspection program that includes the frequency and extent of the inspection
necessary to provide for the continued airworthiness of the rotorcraft. Reference Appendix A,
A27.3 (b)(1).
   b. This chapter should contain a schedule of the interval for all inspections. The inspection
intervals may be in cycles, hours, and/or calendar time.
   c. In the introduction of this chapter, it should explain all required inspections and should
include:
      (1) The different type of inspections.
         (a) Scheduled Inspections.
          (b) Special Inspections.
          (c) Conditional Inspections.
      (2) An explanation of each inspection.
      (3) A list of all inspections (daily, 300-hour, 600-hour, annual, special inspection, etc.).
   d. This chapter should contain the scope of the inspection(s).  It should also describe the
intent of the inspection and should address at least the following:
      (1) What the inspector should be looking for when inspecting the product or appliance.
          (cracks, corrosion, delamination, dents, bends, wear, etc.)
      (2) Location of the product or appliance to be inspected.
      (3) Any special techniques required to inspect the product or appliance.
      (4) Instructions to be followed when inspecting the product or appliance.
      (5) Any tools or equipment required to accomplish the inspection of the product or
         appliance.
      (6) The wear tolerances for a product or appliance when the inspection requires the
         product or appliance to meet a standard.
   e.  This chapter should contain an inspection program which contains an outline of the order
       of the inspections and instructions to be followed during the inspection and should
       include:
         (1) General information such as:
            (a) The title of the inspection.
            (b) Aircraft information (registration number, serial number, total time in service).

REVISION:                                         (PAGE NUMBER)
Revision 4                                                        05-00-00 Page 1


                                                                  Page Apdx A - 23

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →