Appendix A gives an acceptable means for certain powered-lift under §21.17(b). These criteria are not universally applicable CFR requirements; establish the basis for the particular aircraft.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
07/18/2025 AC 21.17-4
Appendix A
(a) Governing and reversible-pitch propellers. Fifteen hundred complete cycles must be made
across the range of forward pitch and rotational speed. In addition, 200 complete cycles of
control must be made from lowest normal pitch to maximum reverse pitch. During each cycle,
the propeller must run for 30 seconds at the maximum power and rotational speed selected by the
applicant for maximum reverse pitch.
(b) Feathering propellers. Fifty cycles of feather and unfeather operation must be made.
PL.3541 Overspeed and overtorque.
(a) When the applicant seeks approval of a transient maximum propeller overspeed, the applicant
must demonstrate that the propeller is capable of further operation without maintenance action at
the maximum propeller overspeed condition. This may be accomplished by:
(1) Performance of 20 runs, each of 30 seconds duration, at the maximum propeller overspeed
condition; or
(2) Analysis based on test or service experience.
(b) When the applicant seeks approval of a transient maximum propeller overtorque, the
applicant must demonstrate that the propeller is capable of further operation without maintenance
action at the maximum propeller overtorque condition. This may be accomplished by
performance of 20 runs, each of 30 seconds duration, at the maximum propeller overtorque
condition.
PL.3542 Components of the propeller control system.
The applicant must demonstrate by tests, analysis based on tests, or service experience on similar
components, that each propeller blade pitch control system component, including governors,
pitch change assem blies, pitch locks, mechanical stops, and feathering system components, can
withstand cyclic operation that simulates the normal load and pitch change travel to which the
component would be subjected during the initially declared overhaul period or during a
minimum of 1,000 hours of typical operation in service.
PL.3543 Propeller hydraulic components.
Applicants must show by test, validated analysis, or both, that propeller components that contain
hydraulic pressure and whose structural failure or leakage from a structural failure could cause a
hazardous propeller effect demonstrate structural integrity by:
(a) A proof pressure test to 1.5 times the maximum operating pressure for one minute without
permanent deformation or leakage that would prevent performance of the intended function.
(b) A burst pressure test to 2.0 times the maximum operating pressure for one minute without
failure. Leakage is permitted and seals may be excluded from the test.
SUBPART K—INSTRUCTIONS FOR CONTINUED AIRWORTHINESS
PL.4101 General.
(a) This subpart specifies requirements for the preparation of Instructions for Continued
Airworthiness as required by PL.1529.
A-49
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Begin with the aircraft and the agreed basis.
Connect the operating concept, aircraft-level failure effects, system architecture and assurance planning. Keep FAA powered-lift criteria and EASA SC-VTOL provisions distinct when developing the safety and certification approach.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.