FAA / Advisory circular

AC 21.17-4

Type Certification—Powered-lift

Follow the FAA powered-lift certification approach and navigate the airworthiness criteria in Appendix A.

Start with the scope.

Appendix A gives an acceptable means for certain powered-lift under §21.17(b). These criteria are not universally applicable CFR requirements; establish the basis for the particular aircraft.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page A-46

PDF page 55 of 64

Enlarge original ↗

Original source view; text reflow has not yet been reviewed

Original FAA AC 21.17-4, PDF page 55
AC 21.17-4 · A-46Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

07/18/2025                                               AC 21.17-4
                                                                        Appendix A

(d) The propeller control system must be designed and constructed so that the failure or
corruption of aircraft-supplied data does not result in hazardous propeller effects.
(e) The propeller control system must be designed and constructed so that the loss, interruption,
or abnormal characteristic of aircraft-supplied electrical power does not result in hazardous
propeller effects. The power quality requirements must be described in the appropriate manuals.
PL.3524 Strength.
(a) The maximum stresses developed in the propeller may not exceed values acceptable to the
Administrator considering the particular form of construction and the most severe operating
conditions.
(b) Engine-driven lift devices must also comply with all applicable design load conditions and
safety factors defined in subpart C.
PL.3533 General.
(a) Each applicant must furnish test article(s) and suitable testing facilities, including equipment
and competent personnel, and conduct the required tests in accordance with 14 CFR part 21.
(b) All automatic controls and safety systems must be in operation unless it is accepted by the
Administrator as impossible or not required because of the nature of the test. If needed for
substantiation, the applicant may test a different propeller configuration if this does not constitute
a less severe test.
(c) Any systems or components that cannot be adequately substantiated by the applicant to the
requirements of these airworthiness criteria are required to undergo additional tests or analysis to
demonstrate that the systems or components are able to perform their intended functions in all
declared environmental and operating conditions.
PL.3534 Inspections, adjustments, and repairs.
 (a) Before and after conducting the tests prescribed in this subpart, the test article must be
subjected to an inspection, and a record must be made of all the relevant parameters, calibrations
and settings.
(b) During all tests, only servicing and minor repairs are permitted. If major repairs or part
replacement is required, the Administrator must approve the repair or part replacement prior to
implementation and may require additional testing. Any unscheduled repair or action on the test
article must be recorded and reported.
PL.3535 Centrifugal load tests.
The applicant must demonstrate that a propeller complies with paragraphs (a), (b) and (c) of this
section without evidence of failure, malfunction, or permanent deformation that would result in a
major or hazardous propeller effect. When the propeller could be sensitive to environmental
degradation in service, this must be considered.
(a) The hub, blade retention system, and counterweights must be tested for a period of one hour
to a load equivalent to twice the maximum centrifugal load to which the propeller would be
subjected during operation at the maximum rated rotational speed.
(b) Blade features associated with transitions to the retention system (for example, a composite
blade bonded to a metallic retention) must be tested either during the test of paragraph (a) of this

                                       A-46

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Begin with the aircraft and the agreed basis.

Connect the operating concept, aircraft-level failure effects, system architecture and assurance planning. Keep FAA powered-lift criteria and EASA SC-VTOL provisions distinct when developing the safety and certification approach.

Explore our eVTOL safety and certification approach →
Source edition and reading coverage

64 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: e1a60e5f5ed4f34764beb0866a0a1b65471832a1cf169ef670a6dd6bf434297e

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →