FAA / Advisory circular

AC 21.17-4

Type Certification—Powered-lift

Follow the FAA powered-lift certification approach and navigate the airworthiness criteria in Appendix A.

Start with the scope.

Appendix A gives an acceptable means for certain powered-lift under §21.17(b). These criteria are not universally applicable CFR requirements; establish the basis for the particular aircraft.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page A-45

PDF page 54 of 64

Enlarge original ↗

Original source view; text reflow has not yet been reviewed

Original FAA AC 21.17-4, PDF page 54
AC 21.17-4 · A-45Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

07/18/2025                                              AC 21.17-4
                                                                        Appendix A

(b) For propellers incorporating a method to select blade pitch below the in-flight low-pitch
position, provisions must be made to sense and indicate to the flightcrew that the propeller blades
are below that position by an amount defined in the installation instructions. The method for
sensing and indicating the propeller blade pitch position must be such that its failure does not
affect the control of the propeller.
PL.3522 Feathering propellers.
(a) Feathering propellers are intended to feather from all flight conditions, taking into account
expected wear and leakage. Any feathering and unfeathering limitations must be documented in
the appropriate manuals.
(b) Propeller pitch control systems that use engine oil to feather must incorporate a method to
allow the propeller to feather if the engine oil system fails.
(c) Feathering propellers must be designed to be capable of unfeathering after the propeller
system has stabilized to the minimum declared outside air temperature.
PL.3523 Propeller control system.
The requirements of this section apply to any system or component that controls, limits, or
monitors propeller functions.
(a) The propeller control system must be designed, constructed and validated to show that:
(1) The propeller control system, operating in normal and alternative operating modes and in
transition between operating modes, performs the functions defined by the applicant throughout
the approved operating conditions and approved flight envelope.
(2) The propeller control system functionality is not adversely affected by the declared
environmental conditions, including temperature, electromagnetic interference (EMI), high
intensity radiated fields (HIRF), and lightning. The environmental limits to which the system has
been satisfactorily validated must be documented in the appropriate propeller manuals.
(3) A method is provided to indicate that an operating mode change has occurred if flightcrew
action is required. In such an event, operating instructions must be provided in the appropriate
manuals.
(b) The propeller control system must be designed and constructed so that, in addition to
compliance with PL.3515:
(1) No single failure results in a hazardous propeller effect;
(2) Local events in the intended aircraft installation will not result in hazardous propeller effects;
(3) The loss of normal propeller pitch control does not cause a hazardous propeller effect under
the intended operating conditions; and
(4) The failure or corruption of data or signals shared across propellers does not cause a
hazardous propeller effect.
(c) Electronic propeller-control-system embedded software must be designed and implemented
by a method approved by the Administrator that is consistent with the criticality of the performed
functions and that minimizes the existence of software errors.


                                       A-45

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Begin with the aircraft and the agreed basis.

Connect the operating concept, aircraft-level failure effects, system architecture and assurance planning. Keep FAA powered-lift criteria and EASA SC-VTOL provisions distinct when developing the safety and certification approach.

Explore our eVTOL safety and certification approach →
Source edition and reading coverage

64 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: e1a60e5f5ed4f34764beb0866a0a1b65471832a1cf169ef670a6dd6bf434297e

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →