FAA / Advisory circular

AC 21.17-4

Type Certification—Powered-lift

Follow the FAA powered-lift certification approach and navigate the airworthiness criteria in Appendix A.

Start with the scope.

Appendix A gives an acceptable means for certain powered-lift under §21.17(b). These criteria are not universally applicable CFR requirements; establish the basis for the particular aircraft.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page A-44

PDF page 53 of 64

Enlarge original ↗

Original source view; text reflow has not yet been reviewed

Original FAA AC 21.17-4, PDF page 53
AC 21.17-4 · A-44Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

07/18/2025                                              AC 21.17-4
                                                                        Appendix A

(g) Unless otherwise approved by the Administrator and stated in the safety analysis, the
following failure definitions apply to compliance with these airworthiness criteria.
(1) The following are regarded as hazardous propeller effects:
(i) The development of excessive drag.
(ii) A significant thrust in the opposite direction to that commanded by the pilot.
(iii) The release of the propeller or any major portion of the propeller.
(iv) A failure that results in excessive unbalance.
(2) The following are regarded as major propeller effects for variable-pitch propellers:
(i) An inability to feather the propeller for feathering propellers.
(ii) An inability to change propeller pitch when commanded.
(iii) A significant uncommanded change in pitch.
(iv) A significant uncontrollable torque or speed fluctuation.
PL.3516 Propeller critical parts.
The integrity of each propeller critical part identified by the safety analysis required by PL.3515
must be established by:
(a) A defined engineering process for ensuring the integrity of the propeller critical part
throughout its service life,
(b) A defined manufacturing process that identifies the requirements to consistently produce the
propeller critical part as required by the engineering process, and
(c) A defined service-management process that identifies the co ntinued airworthiness
requirements of the propeller critical part as required by the engineering process.
PL.3517 Materials and manufacturing methods.
(a) The suitability and durability of materials used in the propeller must:
(1) Be established on the basis of experience, tests, or both.
(2) Account for environmental conditions expected in service.
(b) All materials and manufacturing methods must conform to specifications acceptable to the
Administrator.
(c) The design values of properties of materials must be suitably related to the most adverse
properties stated in the material specification for applicable conditions expected in service.
PL.3519 Durability.
Each part of the propeller must be designed and constructed to minimize the development of any
unsafe condition of the propeller between overhaul periods.
PL.3521 Variable- and reversible-pitch propellers.
(a) No single failure or malfunction in the propeller system will result in unintended travel of the
propeller blades to a position below the in-flight low-pitch position. The extent of any intended
travel below the in-flight low-pitch position must be documented by the applicant in the
appropriate manuals. Failure of structural elements need not be considered if the occurrence of
such a failure is shown to be extremely remote under PL.3515.

                                       A-44

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Begin with the aircraft and the agreed basis.

Connect the operating concept, aircraft-level failure effects, system architecture and assurance planning. Keep FAA powered-lift criteria and EASA SC-VTOL provisions distinct when developing the safety and certification approach.

Explore our eVTOL safety and certification approach →
Source edition and reading coverage

64 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: e1a60e5f5ed4f34764beb0866a0a1b65471832a1cf169ef670a6dd6bf434297e

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →