FAA / Advisory circular

AC 21.17-4

Type Certification—Powered-lift

Follow the FAA powered-lift certification approach and navigate the airworthiness criteria in Appendix A.

Start with the scope.

Appendix A gives an acceptable means for certain powered-lift under §21.17(b). These criteria are not universally applicable CFR requirements; establish the basis for the particular aircraft.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page A-30

PDF page 39 of 64

Enlarge original ↗

Original source view; text reflow has not yet been reviewed

Original FAA AC 21.17-4, PDF page 39
AC 21.17-4 · A-30Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

07/18/2025                                              AC 21.17-4
                                                                        Appendix A

protection unless damage by fire will not cause leakage or spillage of a hazardous quantity of
flammable fluid. For an engine having an integral oil sump of less than 23.7 liters capacity, the
oil sump need not be fireproof or enclosed by a fireproof shield.
(d) An engine component designed, constructed, and installed to act as a firewall must be:
(1) Fireproof;
(2) Constructed so that no hazardous quantity of air, fluid or flame can pass around or through
the firewall; and
(3) Protected against corrosion;
(e) In addition to the requirements of paragraphs (a) and (b) of this section, engine control
system components that are located in a designated fire zone must be fire resistant or fireproof,
as determined by the Administrator.
(f) Unintentional accumulation of hazardous quantities of flammable fluid within the engine
must be prevented by draining and venting.
(g) Any components, modules, or equipment, which are susceptible to or are potential sources of
static discharges or electrical fault currents must be designed and constructed to be properly
grounded to the engine reference, to minimize the risk of ignition in external areas where
flammable fluids or vapors could be present.
(h) High-voltage electrical wiring interconnection systems must be protected against arc faults
that can lead to a fire that could result in hazardous engine effects as defined in PL.3375(g)(2).
Any non-protected electrical wiring interconnects must be analyzed to show that arc faults do not
cause a hazardous engine effect.
PL.3319 Durability.
(a) The engine design and construction must minimize the development of an unsafe condition of
the engine between maintenance intervals, overhaul periods, or mandatory actions described in
the applicable Instructions for Continued Airworthiness.
(b) Each component of the propeller blade pitch control system which is a part of the engine type
design must meet the requirements of sections PL.3521, PL.3523, PL.3542 and PL.3543.
PL.3321 Engine cooling.
(a) Engine design and construction must provide the necessary cooling under conditions in which
the aircraft is expected to operate.
(b) If cooling is required to satisfy the safety analysis as described in PL.3375, the cooling
system monitoring features and usage must be documented in accordance with the requirements
in PL.3305.
PL.3323 Engine mounting attachments and structure.
(a) The maximum allowable limit and ultimate loads for engine mounting attachments and
related engine structure must be specified.
(b) The engine mounting attachments and related engine structure must be able to withstand—
(1) The specified limit loads without permanent deformation; and


                                       A-30

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Begin with the aircraft and the agreed basis.

Connect the operating concept, aircraft-level failure effects, system architecture and assurance planning. Keep FAA powered-lift criteria and EASA SC-VTOL provisions distinct when developing the safety and certification approach.

Explore our eVTOL safety and certification approach →
Source edition and reading coverage

64 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: e1a60e5f5ed4f34764beb0866a0a1b65471832a1cf169ef670a6dd6bf434297e

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →