Appendix A gives an acceptable means for certain powered-lift under §21.17(b). These criteria are not universally applicable CFR requirements; establish the basis for the particular aircraft.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
07/18/2025 AC 21.17-4
Appendix A
PL.3307 Engine ratings and operating limitations.
(a) Engine ratings and operating limitations are established by the Administrator and included in
the type certificate data sheet specified in 14 CFR 21.41, including ratings and limitations based
on the operating conditions and information specified in this section, as applicable, and any other
information found necessary for safe operation of the engine.
(b) For electric engines, ratings and operating limits are established relating to the following:
(1) Shaft power, torque, or thrust; rotational speed; temperature; and time for:
(i) Rated takeoff power or thrust;
(ii) Rated maximum continuous power or thrust; and
(iii) Rated maximum temporary power or thrust and associated time limit.
(2) Duty cycle and the rating at that duty cycle. The duty cycle must be declared in the type
certificate data sheet.
(3) Cooling fluid grade or specification.
(4) Power-supply requirements.
(5) Any other ratings or limitations that are necessary for the safe operation of the engine.
(c) In determining the engine performance and operating limitations, the overall limits of
accuracy of the engine control system, of the engine electrical systems, and of the necessary
instrumentation as defined in PL.3305(a)(6) must be taken into account.
PL.3308 Selection of engine power and thrust ratings.
(a) Requested engine power and thrust ratings must be selected by the applicant.
(b) Each selected rating must be for the lowest power or thrust that all engines of the same type
may be expected to produce under the conditions used to determine that rating.
PL.3315 Materials.
The suitability and durability of materials used in the engine must—
(a) Be established on the basis of experience or tests; and
(b) Conform to approved specifications (such as industry or military specifications) that ensure
their having the strength and other properties assumed in the design data.
PL.3317 Fire protection.
(a) The design and construction of the engine and the materials used must minimize the
probability of the occurrence and spread of fire during normal operation and failure conditions
and must minimize the effect of such a fire.
(b) Except as provided in paragraph (c) of this section, each external line, fitting, and other
component, which contains or conveys flammable fluid during normal engine operation, must be
fire resistant or fireproof, as determined by the Administrator. Components must be shielded or
located to safeguard against the ignition of leaking flammable fluid.
(c) A tank, which contains flammable fluids and any associated shut-off means and supports,
which are part of and attached to the engine, must be fireproof either by construction or by
A-29
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Begin with the aircraft and the agreed basis.
Connect the operating concept, aircraft-level failure effects, system architecture and assurance planning. Keep FAA powered-lift criteria and EASA SC-VTOL provisions distinct when developing the safety and certification approach.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.