FAA / Advisory circular

AC 21.17-4

Type Certification—Powered-lift

Follow the FAA powered-lift certification approach and navigate the airworthiness criteria in Appendix A.

Start with the scope.

Appendix A gives an acceptable means for certain powered-lift under §21.17(b). These criteria are not universally applicable CFR requirements; establish the basis for the particular aircraft.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page A-15

PDF page 24 of 64

Enlarge original ↗

Original source view; text reflow has not yet been reviewed

Original FAA AC 21.17-4, PDF page 24
AC 21.17-4 · A-15Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

07/18/2025                                               AC 21.17-4
                                                                        Appendix A

PL.2255 Protection of structure.
(a) The applicant must protect each part of the aircraft, including small parts such as fasteners,
against deterioration or loss of strength due to any cause likely to occur in the expected
operational environment.
(b) Each part of the aircraft must have adequate provisions for ventilation and drainage.
(c) For each part that requires maintenance, preventive maintenance, or servicing, the applicant
must incorporate a means into the aircraft design to allow such actions to be accomplished.
PL.2260 Materials and processes.
(a) The applicant must determine the suitability and durability of materials used for parts,
articles, and assemblies, accounting for the effects of likely environmental conditions expected in
service, the failure of which could prevent continued safe flight and landing.
(b) The methods and processes of fabrication and assembly used must produce consistently
sound structures. If a fabrication process requires close control to reach this objective, the
applicant must perform the process under an approved process specification.
(c) Except as provided in paragraphs (f) and (g) of this section, the applicant must select design
values that ensure material strength with probabilities that account for the criticality of the
structural element. Design values must account for the probability of structural failure due to
material variability.
(d) If material strength properties are required, a determination of those properties must be based
on sufficient tests of material meeting specifications to establish design values on a statistical
basis.
(e) If thermal effects are significant on a critical component or structure under normal operating
conditions, the applicant must determine those effects on allowable stresses used for design.
(f) Design values, greater than the minimums specified by this section, may be used, where only
guaranteed minimum values are normally allowed, if a specimen of each individual item is tested
before use to determine that the actual strength properties of that particular item will equal or
exceed those used in the design.
(g) An applicant may use other material design values if approved by the Administrator.
PL.2265 Special factors of safety.
(a) The applicant must determine a special factor of safety for each critical design value for each
part, article, or assembly for which that critical design value is uncertain, and for each part,
article, or assembly that is—
(1) Likely to deteriorate in service before normal replacement; or
(2) Subject to appreciable variability because of uncertainties in manufacturing processes or
inspection methods.
(b) The applicant must determine a special factor of safety using quality controls and
specifications that account for each—
(1) Type of application;
(2) Inspection method;

                                       A-15

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Begin with the aircraft and the agreed basis.

Connect the operating concept, aircraft-level failure effects, system architecture and assurance planning. Keep FAA powered-lift criteria and EASA SC-VTOL provisions distinct when developing the safety and certification approach.

Explore our eVTOL safety and certification approach →
Source edition and reading coverage

64 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: e1a60e5f5ed4f34764beb0866a0a1b65471832a1cf169ef670a6dd6bf434297e

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →