FAA / Advisory circular

AC 21.17-4

Type Certification—Powered-lift

Follow the FAA powered-lift certification approach and navigate the airworthiness criteria in Appendix A.

Start with the scope.

Appendix A gives an acceptable means for certain powered-lift under §21.17(b). These criteria are not universally applicable CFR requirements; establish the basis for the particular aircraft.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page A-13

PDF page 22 of 64

Enlarge original ↗

Original source view; text reflow has not yet been reviewed

Original FAA AC 21.17-4, PDF page 22
AC 21.17-4 · A-13Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

07/18/2025                                              AC 21.17-4
                                                                        Appendix A

(d) Engine-driven lift device assemblies, considering loads resulting from flight and ground
conditions, as well limit input torque at any engine-driven lift device rotational speed.
PL.2230 Limit and ultimate loads.
The applicant must determine—
(a) The limit loads, which are equal to the structural design loads unless otherwise specified
elsewhere in these airworthiness criteria; and
(b) The ultimate loads, which are equal to the limit loads multiplied by a 1.5 factor of safety
unless otherwise specified elsewhere in these airworthiness criteria.
Structural Performance
PL.2235 Structural strength.
The structure must support:
(a) Limit loads without—
(1) Interference with the safe operation of the aircraft; and
(2) Detrimental or permanent deformation.
(b) Ultimate loads.
PL.2240 Structural durability.
(a) The applicant must develop and implement inspections or other procedures to prevent
structural failures due to foreseeable causes of strength degradation, which could result in serious
or fatal injuries, or extended periods of operation with reduced safety margins. Each of the
inspections or other procedures developed under this section must be included in the
Airworthiness Limitations Section of the ICA, required by PL.1529.
(b) If safety-by-design (fail-safe) is used to comply with paragraph (a) of this section, safety-by-
inspection (damage tolerance) must also be incorporated to reliably detect structural damage
before the damage could result in structural failure.
(c) For pressurized aircraft:
(1) The aircraft must be capable of continued safe flight and landing following a sudden release
of cabin pressure, including sudden releases caused by door and window failures.
(2) For aircraft with maximum operating altitude greater than 41,000 feet, the procedures
developed for compliance with paragraph (a) of this section must be capable of detecting damage
to the pressurized cabin structure before the damage could result in rapid decompression that
would result in serious or fatal injuries.
(d) The aircraft must be designed to minimize hazards to the aircraft due to structural damage
caused by high-energy fragments from an uncontained engine or rotating machinery failure.
(e) Engine-driven lift devices, control mechanisms, components, and related engine structure
necessary to transmit loads from the engine-driven lift device to the airframe must comply with
the damage tolerance and fatigue criteria of this section.
PL.2241 Aeromechanical stability.


                                       A-13

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Begin with the aircraft and the agreed basis.

Connect the operating concept, aircraft-level failure effects, system architecture and assurance planning. Keep FAA powered-lift criteria and EASA SC-VTOL provisions distinct when developing the safety and certification approach.

Explore our eVTOL safety and certification approach →
Source edition and reading coverage

64 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: e1a60e5f5ed4f34764beb0866a0a1b65471832a1cf169ef670a6dd6bf434297e

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →