FAA / Advisory circular

AC 21.17-4

Type Certification—Powered-lift

Follow the FAA powered-lift certification approach and navigate the airworthiness criteria in Appendix A.

Start with the scope.

Appendix A gives an acceptable means for certain powered-lift under §21.17(b). These criteria are not universally applicable CFR requirements; establish the basis for the particular aircraft.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page A-10

PDF page 19 of 64

Enlarge original ↗

Original source view; text reflow has not yet been reviewed

Original FAA AC 21.17-4, PDF page 19
AC 21.17-4 · A-10Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

07/18/2025                                               AC 21.17-4
                                                                        Appendix A

(a) Exhibit controllable flight characteristics, including but not limited to stalls in straight flight,
turning flight, and accelerated turning flight.
(b) Not have the tendency to inadvertently depart controlled safe flight after a sudden change of
thrust.
(c) Have a clear and distinctive warning that provides sufficient margin to prevent inadvertent
departure from controlled flight.
PL.2155 Ground and water handling characteristics.
For aircraft intended for operation on land or water, the aircraft must have controllable
longitudinal and directional handling characteristics during taxi, takeoff, and landing operations.
PL.2160 Vibration, buffeting, and high-speed characteristics.
(a) Each part of the aircraft must be free from excessive vibration and buffeting under each
appropriate speed and power condition. Vibration and buffeting, for operations up to VD/MD,
must not interfere with the control of the aircraft or cause excessive fatigue to the flightcrew.
Stall warning buffet within these limits is allowable.
(b) For inadvertent excursions beyond the maximum approved speed, the aircraft must be able to
safely recover back to its approved flight envelope without requiring exceptional piloting skill,
strength, or alertness. This recovery may not result in structural damage or loss of control.
PL.2165 Performance and flight characteristics requirements for flight in atmospheric
icing conditions.
(a) An applicant who requests certification for flight in atmospheric icing conditions must show
the following in the icing conditions for which certification is requested:
(1) Compliance with each requirement of this subpart, except those applicable to spins and any
that must be demonstrated at speeds in excess of—
(i) 250 knots calibrated airspeed (CAS);
(ii) VMO/MMO or VNE; or
(iii) A speed at which the applicant demonstrates the airframe will be free of ice accretion.
(b) The applicant must provide a means to detect icing conditions for which certification is not
requested and show the aircraft’s ability to avoid or exit those icing conditions.
(c) The applicant must develop an operating limitation to prohibit intentional flight, including
takeoff and landing, into icing conditions for which the aircraft is not certified to operate.
SUBPART C—STRUCTURES
PL.2200 Structural design envelope.
The applicant must determine the structural design envelope, which describes the range and
limits of aircraft design and operational parameters for which the applicant will show compliance
with the requirements of this subpart. The applicant must account for all aircraft design and
operational parameters that affect structural loads, strength, durability, and aeroelasticity,
including:



                                       A-10

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Begin with the aircraft and the agreed basis.

Connect the operating concept, aircraft-level failure effects, system architecture and assurance planning. Keep FAA powered-lift criteria and EASA SC-VTOL provisions distinct when developing the safety and certification approach.

Explore our eVTOL safety and certification approach →
Source edition and reading coverage

64 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: e1a60e5f5ed4f34764beb0866a0a1b65471832a1cf169ef670a6dd6bf434297e

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →