Appendix A gives an acceptable means for certain powered-lift under §21.17(b). These criteria are not universally applicable CFR requirements; establish the basis for the particular aircraft.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
07/18/2025 AC 21.17-4
Appendix A
(4) Source of lift means one of three sources of lift: thrust‐borne, wing‐borne, and semi-thrust‐
borne. Thrust‐borne is defined as when the aircraft depends principally on engine-driven lift
devices or engine thrust for lift. Wing‐borne is defined as when the aircraft depends principally
on the lift from nonrotating airfoil surfaces. Semi‐thrust‐borne is the combination of thrust‐borne
and wing‐borne, where both forms of lift are used to support the aircraft.
(5) Critical change of thrust means the most adverse effect on performance or handling qualities
resulting from a failure or combination of failures of the propulsive system or flight control
system, when applicable, either singular or in combination, not shown to be extremely
improbable.
(6) Local events are failures of aircraft systems and components, other than the engine and
propeller control system, that may affect the installed environment of the engine and propeller
control system.
(7) Approved flight envelope refers to the range of conditions within which the FAA has deemed
it safe to operate an aircraft. These conditions include, but are not limited to, combinations of
weight and center of gravity, flight profiles, ambient conditions, and likely failures.
(8) Engine-driven lift device is a propeller that generates any combination of lift and principal
forward thrust in semi-thrust-borne flight or lift only in thrust-borne flight.
PL.2010 Accepted means of compliance.
(a) An applicant must comply with these airworthiness criteria using a means of compliance,
which may include consensus standards, accepted by the Administrator.
(b) An applicant requesting acceptance of a means of compliance must provide the means of
compliance to the FAA in a form and manner acceptable to the Administrator.
SUBPART B—FLIGHT
Performance
PL.2100 Weight and center of gravity.
(a) The applicant must determine limits for weights and centers of gravity that provide for the
safe operation of the aircraft.
(b) The applicant must comply with each requirement of this subpart at critical combinations of
weight and center of gravity within the aircraft's range of loading conditions using tolerances
acceptable to the Administrator.
(c) The condition of the aircraft at the time of determining its empty weight and center of gravity
must be well defined and easily repeatable.
PL.2105 Performance data.
(a) Unless otherwise prescribed, the aircraft must meet the performance requirements of this
subpart in—
(1) Still air and standard atmospheric conditions at sea level for aircraft approved for essential
performance; and
(2) Ambient atmospheric conditions within the approved flight envelope for aircraft approved for
increased performance.
A-5
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Begin with the aircraft and the agreed basis.
Connect the operating concept, aircraft-level failure effects, system architecture and assurance planning. Keep FAA powered-lift criteria and EASA SC-VTOL provisions distinct when developing the safety and certification approach.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.