FAA / Advisory circular

AC 21.17-4

Type Certification—Powered-lift

Follow the FAA powered-lift certification approach and navigate the airworthiness criteria in Appendix A.

Start with the scope.

Appendix A gives an acceptable means for certain powered-lift under §21.17(b). These criteria are not universally applicable CFR requirements; establish the basis for the particular aircraft.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page A-40

PDF page 49 of 64

Enlarge original ↗

Original source view; text reflow has not yet been reviewed

Original FAA AC 21.17-4, PDF page 49
AC 21.17-4 · A-40Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

07/18/2025                                              AC 21.17-4
                                                                        Appendix A

performance levels, operational limits, and at any other conditions or power settings, including
energy regeneration, that are required to verify the limit capabilities of the engine.
PL.3388 Temperature limit.
The engine design must demonstrate its capability to endure operation at its temperature limits
plus an acceptable margin. The applicant must quantify and justify the margin to the
Administrator. The demonstration must be repeated for all declared duty cycles and ratings, and
operating environments, which would impact temperature limits.
PL.3389 Operation demonstration.
The engine design must demonstrate safe operating characteristics, including but not limited to
starting, acceleration, power cycling, overspeeding, and power/thrust response in accordance
with PL.3373 throughout the approved flight envelope and operating range. The declared engine
operational characteristics must account for installation loads and effects.
PL.3390 Durability demonstration.
The engine must be subjected to a durability demonstration to show that each part of the engine
has been designed and constructed to minimize any unsafe condition of the system between
overhaul periods or between engine replacement intervals if the overhaul is not defined. This test
must simulate the conditions in which the engine is expected to operate in service, including
typical start-stop cycles, to establish when the initial maintenance is required.
PL.3391 System and component tests.
The applicant must show that systems and components that cannot be adequately substantiated in
accordance with the endurance demonstration or other demonstrations will perform their
intended functions in all declared environmental and operating conditions.
PL.3392 Rotor locking demonstration.
If shaft rotation is prevented by locking the rotor(s), the engine must demonstrate:
(a) Reliable rotor locking performance;
(b) Reliable rotor unlocking performance; and
(c) That no hazardous engine effects, as specified in PL.3375(g)(2), will occur.
PL.3393 Teardown inspection.
(a) After the endurance and durability demonstrations have been completed, the engine must be
completely disassembled. Each engine component and lubricant must be eligible for continued
operation in accordance with the information submitted for showing compliance with PL.1529.
(b) Each engine component having an adjustment setting and a functioning characteristic that can
be established independent of installation on or in the engine must retain each setting and
functioning characteristic within the established and recorded limits at the beginning of the
endurance and durability demonstrations.
(c) If a teardown cannot be performed for all engine components in a non-destructive manner,
then the inspection or replacement intervals for these components and lubricants must be:
(1) Established based on the endurance and durability demonstrations; and


                                       A-40

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Begin with the aircraft and the agreed basis.

Connect the operating concept, aircraft-level failure effects, system architecture and assurance planning. Keep FAA powered-lift criteria and EASA SC-VTOL provisions distinct when developing the safety and certification approach.

Explore our eVTOL safety and certification approach →
Source edition and reading coverage

64 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: e1a60e5f5ed4f34764beb0866a0a1b65471832a1cf169ef670a6dd6bf434297e

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →