(a) Control surfaces and supporting hinge brackets must be designed for inertia loads acting parallel to the hinge line. (b) In the absence of more rational data, the inertia loads may be assumed to be equal to KW, wher…
Text as of November 12, 2026
The reference collection
Search a citation or topic, narrow the collection and see what each source can tell you.
eCFR text: November 12, 2026 · FAA DRS capture: November 17, 2026
Dated source collection · automatic acquisition not yet scheduled
505–512 of 1,876 references
(a) Control surfaces and supporting hinge brackets must be designed for inertia loads acting parallel to the hinge line. (b) In the absence of more rational data, the inertia loads may be assumed to be equal to KW, wher…
Text as of November 12, 2026
(a) Longitudinal, lateral, directional, and drag control system and their supporting structures must be designed for loads corresponding to 125 percent of the computed hinge moments of the movable control surface in the…
Text as of November 12, 2026
(a) General. The maximum and minimum pilot forces, specified in paragraph (c) of this section, are assumed to act at the appropriate control grips or pads (in a manner simulating flight conditions) and to be reacted at t…
Text as of November 12, 2026
(a) Each dual control system must be designed for the pilots operating in opposition, using individual pilot forces not less than— (1) 0.75 times those obtained under § 25.395; or (2) The minimum forces specified in §…
Text as of November 12, 2026
Secondary controls, such as wheel brake, spoiler, and tab controls, must be designed for the maximum forces that a pilot is likely to apply to those controls. The following values may be used: Pilot Control Force Limits…
Text as of November 12, 2026
The effects of trim tabs on the control surface design conditions must be accounted for only where the surface loads are limited by maximum pilot effort. In these cases, the tabs are considered to be deflected in the dir…
Text as of November 12, 2026
(a) Trim tabs. Trim tabs must be designed to withstand loads arising from all likely combinations of tab setting, primary control position, and airplane speed (obtainable without exceeding the flight load conditions pres…
Text as of November 12, 2026
(a) The flight control systems and surfaces must be designed for the limit loads generated when the airplane is subjected to a horizontal 65-knot ground gust from any direction while taxiing and while parked. For airplan…
Text as of November 12, 2026
Remove a filter, use fewer words or include historical and proposed publications. An empty result does not mean that the FAA has no relevant material.
Clear filtersSearch the wider FAA DRS collection ↗Orders, decisions and issue-paper sources →Source coverage
1,177 section entries, 24 appendices and 3 SFAR entries as of November 12, 2026. Tables and 102 original graphics are included. Text inside graphics is not indexed.
Sections, appendices and included SFARs from Parts 21, 23, 25, 27 and 29 are searchable. Historical CFR editions are not included. Source tables and graphics are retained; text inside graphics is not indexed.
OFR/GPO eCFR ↗1,689 DRS catalogue records: 656 current and 1033 historical. 6 ACs have complete source copies and a separate search within each document.
Records returned by the FAA DRS AC feed, including current and historical editions. Other FAA collections may contain additional publications. AC PDF contents are not included in this collection search. Each hosted AC has its own full-document search. Your search is not sent to the FAA.
FAA DRS ↗FAA AC catalogue ↗19 selected FAA, EASA and industry publication notes. This is not a complete EASA collection.
Reviewed notes and source links for FAA, EASA, SAE and EUROCAE publications. Proposed material and research are labelled. Licensed standards remain with their publishers.
Read selected reference notes →Additional official collections →This is an independent resource. The eCFR is an editorial compilation, not the official legal edition of the CFR. Dates, topic tags and source associations do not establish your programme’s certification basis. Confirm applicability and the required edition at the source.
Bring the aircraft or system, the applicable basis and the question your team needs to resolve.
Conventional Aircraft
Safety and certification support for fixed wing aircraft and the systems that make them work.
Proposed sector introduction for review.
Rotorcraft
Connect rotorcraft safety, system architecture and certification evidence.
Proposed sector introduction for review.
eVTOL & advanced air mobility
Bring safety and certification thinking into emerging aircraft programmes from the outset.
Proposed sector introduction for review.
Certification & DER support
Tell us about the aircraft or system, the approval sought, its stage of development and the question you need to resolve.
aero@aerospace.consultingA focused review, an agreed compliance package or ongoing support alongside your team.
This opens your email application.
System safety support
Tell us about the aircraft or system, its stage of development and the safety question you need help answering.
aero@aerospace.consultingA focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
aero@aerospace.consultingCertification planning, a system safety review, or ongoing technical support for your team.
This opens your email application.
Experience & approach
Tell us about the aircraft or system, its development stage, your next milestone and the technical question you need to resolve.
aero@aerospace.consultingWe can then agree whether a focused review, a defined work package or ongoing support is the right starting point.
This opens your email application.
AI/ML assurance & certification readiness
Tell us what the AI will do, who will rely on its output, the aircraft or engineering process involved, and the next decision you need to make.
aero@aerospace.consultingWe can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.
aero@aerospace.consultingA focused engineering review or ongoing support with requirements, architecture and development assurance.
This opens your email application.
A technical conversation
Tell us about your aircraft or system, the reference you are using and the decision your team needs to make.
aero@aerospace.consultingWe can help connect the guidance to your safety, systems engineering or certification work.
This opens your email application.